Recent Posts

Topics with their latest replies in reversed order
	WittyPi4 L3V7 - pi zero 2w fails to fully shutdown By jannsta 1 week ago \| Last Post: 2 days ago Forum Technial Support / Discussion
	so has the wittypi been tested to work over long p... 2 days ago By janns... It is likely that your Raspberry Pi crashed during... 1 week ago By uugea... Hardware: WittyPi4 L3V7 <-> pi zero 2w pow... 1 week ago By janns...
	My vivid unit and extender cannot locate the GPSDR++ program! By rpgpublicity 3 days ago \| Last Post: 2 days ago Forum Technial Support / Discussion
	Please show us the full output on your command lin... 2 days ago By uugea... Received my Vivid unit and extender version 2 toda... 3 days ago By rpgpu...
	Witty Pi 4 L3V7: looses time 10sec per day By yww 2 years ago \| Last Post: 3 days ago Forum Technial Support / Discussion
	Interesting. I will check that. Thanks 3 days ago By nolwe... @nolwenn This is definitely not normal, that co... 3 days ago By uugea... Hello @uugearAfter 24h I have about 1s of delay so... 4 days ago By nolwe... view all posts
	Cannot enable GPU acceleration By davemcallister 5 days ago \| Last Post: 5 days ago Forum Technial Support / Discussion
	@uugear, that worked perfectly. Thank you! 5 days ago By davem... @davemcallister this has nothing to do with the po... 5 days ago By uugea... I forgot to add that I am using the Extender 2, an... 5 days ago By davem...
	Install Witty Pi 4 Mini with repo/WittyPi4/install.sh causes failures by I2C-adress By Bert97 2 weeks ago \| Last Post: 2 weeks ago Forum Technial Support / Discussion
	Good Morning,There's good news. The Zero2W with Tr... 2 weeks ago By Bert9... @nokellner Witty Pi 3 has been discontinued.The la... 2 weeks ago By uugea... to find the root cause with try /error needs addit... 2 weeks ago By Bert9... view all posts
	Witty 4 L3V7 enters to constant loop of turn off and on By slavag 2 weeks ago \| Last Post: 2 weeks ago Forum Technial Support / Discussion
	@admin yes, sounds reasonable. Thanks 2 weeks ago By slava... @slavag Witty Pi can only "see" the voltage from y... 2 weeks ago By uugea... @admin Thanks for your quick reply. I also su... 2 weeks ago By slava... view all posts
	Released today: Witty Pi 5 Python library By Josh Burnett 2 weeks ago \| Last Post: 2 weeks ago Forum Technial Support / Discussion
	Thanks for sharing 🙂 2 weeks ago By uugea... I've been playing around some with the Witty Pi 5 ... 2 weeks ago By Josh ...
	Wittypi 4 RTC problem By marekb 3 weeks ago \| Last Post: 2 weeks ago Forum Technial Support / Discussion
	@marekb please do not ask different questions unde... 2 weeks ago By uugea... Thanks that did the trick. One more question: c... 2 weeks ago By marek... You have installed the wrong version of software.S... 3 weeks ago By uugea...
	Witty PI 4 L3V7 unexpected shutdown By CarstenR 2 weeks ago \| Last Post: 2 weeks ago Forum Technial Support / Discussion
	@admin thank you for the advice. The cell should s... 2 weeks ago By Carst... Your use case assumes the battery provides enough ... 2 weeks ago By uugea... I have mobile setups with PI4Bs and L3V7 with v7 f... 2 weeks ago By Carst...
	Vue on vivid unit with extender 2 and VU GPSDR By asw 3 weeks ago \| Last Post: 3 weeks ago Forum Technial Support / Discussion
	We recently updated the software for Vivid Unit Ex... 3 weeks ago By uugea... I have recently purchased the above and assembled ... 3 weeks ago By asw
	Witty Pi 3 Mini schedule malfunction (Raspbian 1:6.12.47 Trixie ) By Bert97 3 weeks ago \| Last Post: 3 weeks ago Forum Technial Support / Discussion
	@nokellner the short pulling-down on GPIO-4 is a d... 3 weeks ago By uugea... @uugear thanks for the additional info. Using a... 3 weeks ago By Bert9... @nokellner On Witty Pi 3 Mini, the GPIO-4 connects... 3 weeks ago By uugea... view all posts
	keyboard case for vivid unit By tampaflorida083 2 years ago \| Last Post: 4 weeks ago Forum Technial Support / Discussion
	I meant case and not cave 4 weeks ago By Georg... Hi, my name is Lee. I would be interested in a cas... 4 weeks ago By Georg... If only someone came up with a 3D printable enclos... 2 years ago By Alexa... view all posts

No results